Recommendation of UZIN adhesive systems for Barlinek SPC floors
| Product \ Floor type | Anhydrite screed | Cement screed | Oriented strand board (OSB) | Website |
| ADHESIVE SYSTEM | ||||
| Primer | UZIN PE 360Plus (to be applied under the adhesive)
UZIN PE 414 or UZIN PE 412 (in case of installation directly on the floor substrate) |
UZIN PE 360Plus (to be applied under the adhesive)
UZIN PE 414 or UZIN PE 412 (in case of installation directly on the floor substrate) |
UZIN PE 630 (used before possible filling of the oriented strand board)
No priming is required after sanding the oriented strand board. |
www.uzin.com |
| Adhesive for dry rooms
Note: only for absorbent surfaces |
UZIN KE 68T | UZIN KE 68T | UZIN KE 68T | www.uzin.com |
| Adhesive for dry and humid rooms, e.g. bathrooms * | UZIN MK90 ; UZIN MK92S | UZIN MK90 ; UZIN MK92S | UZIN MK90 ; UZIN MK92S | www.uzin.com |
| Tool – serrated trowel type | B1 or B2 | B1 or B2 | B1 or B2 | |
| ADDITIONAL MATERIALS | ||||
| Self levelling compound** | UZIN NC105 lub UZIN NC110 | UZIN NC 150 | UZIN NC 115 | www.uzin.com |
| Quick-setting filler compound | UZIN NC 112 Turbo or UZIN NC 111 BiColor | UZIN NC 152 Turbo or UZIN NC 170 LevelStar | UZIN NC 112 Turbo | www.uzin.com |
* In wet rooms, use a damp proofing system based on the codex Hydrostop membrane glued using the UZIN MK 90 adhesive with the use of codex corner tapes (BST and DB series codex tapes). Install the corner strips using the codex SK100 or codex Epo2000.
**If it is required to level the substrate, the choice of self-levelling compound can be consulted with the Uzin Utz technical department.
Recommendation of BAUTEC adhesive systems for Barlinek SPC floors
| Product \ Floor type | Anhydrite screed | Cement screed | Oriented strand board (OSB) | Website |
| ADHESIVE SYSTEM | ||||
| Primer | TEC PRIMER D concentrate OKATMOS EG 20 concentrate OKATMOS UG 30 concentrate |
TEC PRIMER D 1:1 mix with water OKATMOS EG 20 1:1 mix with water OKATMOS UG 30 1:1 mix with water |
No priming is required after sanding the oriented strand board.
No sanding – priming with concentrate is required |
www.bautec.pl www.kiesel.com.pl |
| Adhesive for dry rooms without underfloor heating. Surfaces that are not exposed to sunlight | MULTITEC (dispersion) | MULTITEC (dispersion) | MULTITEC (dispersion) | www.bautec.pl |
| Tool – serrated trowel type
ATTENTION: Gluing to self-levelling compound / filler compound |
TKB B2
TKB B3 |
TKB B2
TKB B3 |
TKB B2
TKB B3 |
|
| Adhesive for dry rooms and with high humidity, e.g. bathrooms | TEC SPU (one-component)
STAUF R105 (two-component) KIESEL OKAMUL PU (two-component) |
TEC SPU (one-component)
STAUF R105 (two-component) KIESEL OKAMUL PU (two-component) |
TEC SPU (one-component)
STAUF R105 (two-component) KIESEL OKAMUL PU (two-component) |
www.bautec.pl www.kiesel.com.pl |
| Tool – serrated trowel type
Bonding to a properly prepared screed* |
TKB B7
TKB B9 |
TKB B7
TKB B9 |
TKB B7
TKB B9 |
www.bautec.pl www.kiesel.com.pl |
| Tool – serrated trowel type
Bonding to a self-levelling compound / filler compound |
TKB B2
TKB B3 |
TKB B2
TKB B3 |
TKB B2
TKB B3 |
www.bautec.pl www.kiesel.com.pl |
| ADDITIONAL MATERIALS | ||||
| Self levelling compound* | SERVOPLAN, SERVOMULTI SERVOFIX
SERVOALPHA |
SERVOPLAN
SERVOMULTI, SERVOFIX SERVOALPHA |
Not required for stable and evenly installed boards (no protruding edges) | www.kiesel.com.pl |
| Quick-setting filler compound | SERVOFINE F333 | SERVOFINE F333 | SERVOFINE F333
(for levelling protrusions and local voids) |
www.kiesel.com.pl |
* Properly prepared screed: below allowable residual moisture / flat / little unevenness / clean / proper stability – no cracks – homogeneous structure – in accordance with the requirements of the floor manufacturer.
** If required, the selection of a self-levelling compound must be consulted with the Bautec Polska Sp.zo.o. technical department.
